Kryptex × GMiner ASIC Firmware

مهم! لتثبيت برنامج Kryptex x GMiner الثابت استخدم Toolkit، يجب أن يكون البرنامج الثابت لـ ASIC قبل مارس 2024 خطوة 1

تنزيل مجموعة أدوات البرنامج الثابت

خطوة 2

افتح مجموعة الأدوات → انقر على “مجموعة جديدة” → أدخل اسم المجموعة ونطاق عنوان IP المحلي → انقر على “موافق”، ثم “فحص الشبكة المحلية”

خطوة 3

اختر المجموعة الجديدة، ثم اختر ASIC من القائمة، وانقر على “تثبيت البرنامج الثابت”

خطوة 4

انتظر حتى تكتمل عملية التثبيت، ثم انقر على “تم”

هذا كل شيء - تم تثبيت البرنامج الثابت الجديد وسيعاد تشغيل جهاز التعدين تلقائيًا.

+Added support for Hiveon ASIC Hub

+Added coloring of heatmap according to the temperature of the chip

+Added use of the device serial number in the status

+Added support for APW111721b and APW111721c power supplies

+Added support for T19 Pro Hyd (HHB56702)

+Added support for S19 Pro Hyd (HHB42602, HHB42701, HHB42711, TH401)

+Added support for S19 Pro+ Hyd (HHB42601, HHB42631)

+Added support for S19 XP Hyd (HHB56601, HHB56611, HHB56613, HHB56701)

+Added support for S19 XP+ Hyd (HHB68701, HHB68703, HHB68704, H6HB68702)

+Added support for U3S19XP+H (H1HB68601)

+Added support for S19e XP Hyd (H6HB56702)

+Added support for U3S19EXPH (H1HB56703)

+Added support for S21 Hyd (HHB68501, HHB68502, HHB68503, HHB68504, HHB68505, HHB68601, HHB68602)

+Added support for S21 Pro Hyd (H6HB70601)

+Added support for S21e XP Hyd (H6HB70602)

+Added support for S21 XP Hyd (H6HB70501)

+Added support for U3S21EXPH (H1HB70601)

+Extends the voltage limits for power supplies (allows to select higher profiles for autotuning)

+Added S19k Pro submodels: BHB56906, BHB56907

+Added an option to set the time zone (correct time in downloaded logs)

+Added chips heatmap for S21 Pro and S21 XP

+Added support for the S19 XP+ (BHB68707, BHB68709)

+Added support for the S21 XP submodel (A3HB70503)

+Added display of ambient temperature for Amlogic control board (S21+, S21 Pro, S21 XP)

+Improved compatibility with the APW121215E power supply

+Added toolkit statistics export to a .CSV file

+Added display of error/warning in the web interface page header

+Added support of older OS for Toolkit (Windows 7 without Direct3D 12)

+Decreased Toolkit executable size by 10Mb, current Toolkit size is 37Mb (offline installer with embedded firmware for all control boards)

Toolkit:

+Added display of hashboard status, allows viewing errors by hashboard

+Added the ability to enable/disable miner search mode

Miner:

+Improved compatibility with power supplies

+Added backup saving for EEPROM, allowing the miner to start even if there are EEPROM issues

+Improved network connection failure handling logic

Web Interface:

+When switching performance profiles in manual temperature tuning mode, the selected temperature tuner settings are saved

+Improved fan control algorithm in auto mode

+Added the ability to configure the following options in the Toolkit: quiet fan mode, do not stop mining when the internet connection is lost

+Improved support for S21 Pro and S21 XP devices

+Added quiet fan mode (fan speed 50% while hash board cooling)

+Added option to allow mining without internet (allows keep ASIC at working temperature)

+Improved compatibility with mining pools

+Added S21+ submodels support: A3HB70601, A3HB70602, A3HB70603, A3HB70501, A3HB70502

+Added the ability to install GMiner on Bitmain stock firmware from late February 2024, including firmware from 2025 (no longer required to downgrade the stock device to an older firmware version)

+Improved logic for returning from a backup pool to the main

+Added S21+ submodels support: A3HB70702, A3HB70703

+Improved logic for switching to backup pools, detects domain blocking by the provider and switching to the next pool

+Reworked the option to ignore broken temperature sensors. Now, at least one working temperature sensor is required for mining. Specifying a minimum number of working sensors is no longer required

+Added an option to enable/disable DNS over HTTPS, allowing you to hide pool addresses from the provider